• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Get a New Key for Subaru

If your Subaru has keys, you can lock and unlock it with the push of a button. But, if your key fob is tossed into the ocean or gets a bath in the washer You may be trying to figure out how to get it working again.

Fortunately our Stocker Subaru dealership has a few suggestions to assist you. You'll have to unzip the key fob case in order to find the transmitter circuitry.

How do I get a new Key

Finding a new key for a Subaru is much simpler than you think. You can get a key from a dealer, a locksmith, or on the internet. The cost will depend on the location where you purchase the key and if it needs to be programed. It also varies based on the type of key (transponder or smart fob? Push to start or regular non-transponder?)

If you're looking for a new key for your vehicle, you'll want to contact an auto locksmith that specializes in Subaru cars. They'll know about the unique key fobs, as well as the key programming that is included with them. If you're unsure which type of key you have, look at the sticker on your windshield to figure it out.

Some keys have Remote Start features which allow you to start your vehicle from the comfort of your home. However, you'll need to have the VIN number for your vehicle which is on the label inside the door of the driver or in the owner's manual.

Subaru models made after 2000 come with a transponder key that disables the computer in the engine. Keys like these can't be duplicated using the same tools that are used to cut traditional metal keys, so you'll have to visit a locksmith or dealership to purchase replacement keys. A new key costs between $50 and $250 depending on the type of key.

How to get a replacement key

There are a variety of ways to get an alternative key for your Subaru, based on the kind of car you have (chip intelligent fob, chip "push to start" remote or a standard metal key). You can purchase an online replacement key, contact the dealership which you purchased the vehicle from, or an auto locksmith that has the proper equipment to make keys like this. You can purchase the replacement subaru keys key from your dealer. It is guaranteed to fit your vehicle and is covered by warranty and will be programmed to the specific model of your vehicle.

For a chipkey dealers will need to have the codes for your specific vehicle, which is only possible at the dealer where you purchased the car. This can be a challenge because you'll have to bring your car to the dealer or have a locksmith visit and code the key.

The majority of locksmiths and hardware stores have a variety of keys that are blank. To remove the battery, you'll need to make use of a flathead screwdriver or a metal key. Replace the old battery with an CR2032 coin cell, and snap the encasement together.

How To Replace Lost Subaru Key do I obtain a key fob

A key fob, or remote control, is a small device that allows access to your car's electronic systems. They can unlock and start your car, lock it, activate the alarm, and so on. If your Subaru key fob isn't working properly, you may need to replace it. Make sure you get the right type of fob for your vehicle. According to Consumer Reports, off-brand fobs could cause problems for the car's immobilizer.

If you have a newer subaru outback key fob model, it's likely it's equipped with the smart key system. They require a special programming process for compatibility with your vehicle. The dealer should be able to do this and your warranty or roadside service program could be able to cover the cost.

Older subaru replacement key models come with a standard lock that can be duplicated at a hardware store. You can also buy blank keys at online stores that provide subaru impreza key fob replacement logo keys.

You can fix the issue with your battery on your older Subaru at home, without having to visit a mechanic or pay for a key duplication service. There is a tiny crevice between the front and the back of the key fob. Use a flathead screwdriver to break the two halves. There's a flat battery inside. Remove the old battery and put the new 2025 type battery in and make sure the correct side is facing up. Then, put the key of metal inside and then pop it all together.

How do I replace a key fob

In the past, people would buy the keyfob for a low price at a hardware store or on the internet and then bring it to a dealer or locksmith to get it cut and programmed. It's still possible to do this, however it's preferential to deal with the dealer. This will prevent the key from being copied and ensure that the new key fob has been correctly programmed for your car. This is especially important if you have a newer model that requires specialized programming such as those that provide features such as auto-parking and window rolling.

They are great to use when driving your Subaru in Gilroy but they can be an issue when the buttons stop working. Fortunately, replacing the battery of your key fob is simple, and you can even do it yourself if know how.

Begin by locating the tiny space in the seam which separates the front from the back of your fob. Use a flathead screwdriver or the edge of a screwdriver made from metal to remove the fob and then look inside for the round flat battery. Remove the old battery and replace it with a 2032 battery. Make sure that the battery is facing the same way as the original. Then, put your device back together.

In the future you might be able to get your car keys replaced with "smart" keys that come with additional functionality. But, until then, you can enjoy all of the benefits of Subaru's key fob. This includes the ability to open your windows while keeping your engine running.